[Nut-upsuser] GE lanpor ups monitored with SNMP stop to monitor after upgrade

[Александр Деревянко]

Hello All !

Recently I have upgraded NUT to 2.4.1, and now I can't monitor old IMV 
LanPro S3 UPS with old SNMP board.
Previously it is monitored OK, but now snmp-ups refuses to start:

[root at perforce /usr/local/etc/nut]# /usr/local/libexec/nut/snmp-ups -a 
lanproups -DDDDDDD
Network UPS Tools - Generic SNMP UPS driver 0.44 (2.4.1)
debug level is '7'
SNMP UPS driver : entering upsdrv_initups()
SNMP UPS driver : entering nut_snmp_init(snmp-ups, 192.9.100.149, v1, 
public)
SNMP UPS driver : entering load_mib2nut(auto)
load_mib2nut: trying apcc mib
nut_snmp_get(.1.3.6.1.4.1.318.1.1.1.1.1.1.0)
load_mib2nut: trying mge mib
nut_snmp_get(.1.3.6.1.4.1.705.1.1.1.0)
load_mib2nut: trying netvision mib
nut_snmp_get(.1.3.6.1.4.1.4555.1.1.1.1.1.1.0)
load_mib2nut: trying pw mib
nut_snmp_get(1.3.6.1.4.1.534.1.1.2.0)
load_mib2nut: trying ietf mib
nut_snmp_get(1.3.6.1.2.1.33.1.1.1.0)
load_mib2nut: trying aphel_genesisII mib
nut_snmp_get(.1.3.6.1.4.1.17373.3.1.1.0)
load_mib2nut: trying aphel_revelation mib
nut_snmp_get(.1.3.6.1.4.1.13742.1.1.12.0)
load_mib2nut: trying raritan mib
nut_snmp_get(.1.3.6.1.4.1.13742.1.1.12.0)
No supported device detected
[root at perforce /usr/local/etc/nut]#


 From ups.conf:

[lanproups]
        driver = snmp-ups
        port = 192.9.100.149



I can ping UPS, I can telnet to it, but I can't monitor it:

[root at perforce /usr/local/etc/nut]# telnet 192.9.100.149
Trying 192.9.100.149...
Connected to 192.9.100.149.
Escape character is '^]'.

GEDE SNMP card login:GE
Password: **
---<<Current config>>---<<Code v1.84 
b1.14>>---[-]---[MAC=00:50:c2:09:73:a2]---
   [IP=192.9.100.149] [mask=255.255.255.0] [gateway=0.0.0.0]
-----------------------------------------------------------------------------
1. boot-method    = [configured ip/mask/gw]    R. clear reset count [45]
2. ip-address     = [192.9.100.149]             T. ping
3. subnet mask    = [255.255.255.0]             U. trap config
4. gateway        = [0.0.0.0]             V. responsible e-mail
5. trap addresses = [0.0.0.0] [0.0.0.0] [0.0.0.0] [0.0.0.0]
6. trap community = [public] [public] [public] [public]
7. trap UDP port  = [162] [162] [162] [162]     W. modaddr = [0]
8. get-community  = [public]
9. set-community  = [public]
A. sys-contact    = [The contact person for this agent]
B. sys-name       = [The administrative name of the agent]
C. sys-location   = [Somethere]
D. upsName        = [lanproups]
E. upsAttachedDev = [xit]
F. snmpport       = [161]    H. telnet server  = [on]
G. httpport       = [80]     I. http server    = [on]
J. telnet/http username = [GE]
K. change telnet/http password   L. update firmware   M. MAC   N. reboot
O. cardaddr = [0]   P. upsaddr = [0]   Q. logout   S. ethernet = [Auto]
GE>

---------------------------

 From my previous expirience, I know, that this SNMP board for some 
reason deny to report UPS temperature (everything else is OK).
May be, it's the problem for NUT 2.4.1?