Hi Klaus,<br>
<br>
Thanks for your much appreciated feedback.<br>
<br>
Klaus Holler wrote:<br>
&gt; Hello,<br>
&gt;<br>
&gt;I just wanted to report that the Back-UPS RS 800 works with the<br>
&gt;Network UPS Tools. Currently I use the following (Ubuntu breezy)<br>
&gt;debian packages on kernel 2.4.31:<br>
&gt;ii&nbsp;
nut&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;
2.0.2-1build1<br>
&gt;ii&nbsp;
nut-usb&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;
2.0.2-1build1<br>
&gt;<br>
&gt;lsusb reports:<br>
&gt;ID 051d:0002 American Power Conversion Back-UPS Pro 500/1000/1500<br>
&gt;<br>
&gt;With hidups I get this status:<br>
&gt;<br>
&gt;# upsc myups@localhost<br>
&gt;battery.charge: 100<br>
&gt;battery.chemistry: PbAc<br>
&gt;battery.runtime: 1162<br>
&gt;battery.voltage: 27.4<br>
&gt;<a href="http://driver.name">driver.name</a>: hidups<br>
&gt;driver.parameter.port: /dev/usb/hiddev0<br>
&gt;driver.version: 2.0.2<br>
&gt;ups.delay.shutdown: -1<br>
&gt;ups.delay.start: 0<br>
&gt;ups.load: 410<br>
&gt;ups.mfr: American Power Conversion<br>
&gt;ups.model: Back-UPS BR&nbsp; 800 FW:9.o2 .I USB FW:o2<br>
&gt;ups.serial: QB0420243302<br>
&gt;ups.status: OL<br>
&gt;<br>
&gt;Only one issue is annoying: that the syslog is clutter with lots of<br>
&gt;... hidups[8850]: Ignoring x86 page event 0xff860080 (0)<br>
&gt;... hidups[8850]: Unhandled event: 0x840032 (5000)<br>
&gt;<br>
&gt;<br>
&gt;newhidups also can communicate with the UPS, the status is a little<br>
&gt;more verbose:<br>
&gt;<br>
&gt;# upsc myups@localhost<br>
&gt;battery.charge: 100<br>
&gt;battery.charge.low: 10<br>
&gt;battery.runtime: 1192<br>
&gt;battery.temperature: 302.0<br>
&gt;battery.voltage: 27.0<br>
&gt;battery.voltage.nominal: 24.0<br>
&gt;<a href="http://driver.name">driver.name</a>: newhidups<br>
&gt;driver.parameter.port: /dev/usb/hiddev0<br>
&gt;driver.version: 2.0.2<br>
&gt;driver.version.data: APC HID 0.7<br>
&gt;driver.version.internal: 0.23<br>
&gt;input.voltage: -159357104.0<br>
&gt;output.voltage: 230.0<br>
&gt;output.voltage.target.line: 230.0<br>
&gt;ups.delay.shutdown: -1<br>
&gt;ups.firmware: 9.o2 .I<br>
&gt;ups.firmware.aux: o2<br>
&gt;ups.load: 40<br>
&gt;ups.mfr: American Power Conversion<br>
&gt;ups.model: Back-UPS BR&nbsp; 800<br>
&gt;ups.serial: QB0420243302<br>
&gt;ups.status: OL<br>
&gt;ups.temperature: 302.0<br>
&gt;ups.test.result: No test initiated<br>
&gt;<br>
&gt;But then syslog is cluttered every two seconds with &quot;... kernel:<br>
&gt;usbdevfs: usb_submit_urb returned -22&quot; instead, so I reverted back to<br>
&gt;the recommended hidups ;-)<br>
<br>
newhidups will soon replace hidups. So we'll have to deal with the<br>
remaining problems. There have been lots of improvements in<br>
newhidups since Peter joigned us...<br>
@Peter: have you experienced the same problems with the latest newhidups?<br>
<br clear="all">Arnaud Quette<br>-- <br>Linux / Unix Expert - MGE UPS SYSTEMS - R&amp;D Dpt<br>Network UPS Tools (NUT) Project Leader - <a href="http://www.networkupstools.org/">http://www.networkupstools.org/</a><br>Debian Developer - 
<a href="http://people.debian.org/~aquette/">http://people.debian.org/~aquette/</a><br>OpenSource Developer - <a href="http://arnaud.quette.free.fr/">http://arnaud.quette.free.fr/</a>