<div dir="ltr"><div>This post is to share and ask for confirmation of the accuracy of my thinking in relation to mapping the results of the measurements to the configuration variables provided.</div><div><br></div><div><br></div><div>While setting up for this latest test I noticed an that the 60W bulb, when combined with 3 power factor correcting PSUs of lower wattage devices, had an effect of '6 units' of power output.</div><div><br></div><div>This leads me to a more logical conclusion of the percentage actually representing approximately 9-10 watts per percent, but the UPS either having difficulty measuring a more inductive loading or such a low loading.</div><div><br></div><div>In any event, even though I measured a voltage of 24.40 at the start of the lower power test I'll pick what I guess is the more conservative value seen in the previous test.</div><div>Similarly a smaller sample period allowed the observation of slightly lower low voltages, which I shall also ignore.</div><div><br></div><div>After 29 min at approximately 10 units of load (it seemed to flux between a mode average of 10 and 12 depending on which output winding was selected) the incessant beeping stopped.</div><div><br></div><div>I'll round 1740 down for some additional padding.</div><div><br></div><div><span style="font-family:monospace">[eaton5e]
<br>       driver = nutdrv_qx
<br>        port    = auto
<br>        vendorid = 06da
<br>        productid = 0003</span></div><div><span style="font-family:monospace">       </span>default.battery.voltage.high = 24.10<span style="font-family:monospace"><br></span></div><div><div class="gmail_msg"><span style="font-family:monospace">       </span>default.battery.voltage.low = 21.50<br class="gmail_msg"></div><div class="gmail_msg"><span style="font-family:monospace">       </span>runtimecal = 450,32,1700,10</div><br class="inbox-inbox-Apple-interchange-newline"></div><div><br></div><div>However, having just 100% drained (until the UPS shut it's self off) the battery, and having given it only a few min to recharge a bit those settings give an incorrect charge reading.</div><div><br></div><div>Should the default.battery.voltage.high be the value seen during on-line power conditions (charged up)?</div><div><br></div><div>Will that have a negative effect on the (safe) accuracy of the remaining runtime?</div><div><br></div><div><span style="font-family:monospace"><b>battery.charge: 100
<br></b>battery.voltage: 24.20
<br>battery.voltage.high: 24.10
<br>battery.voltage.low: 21.50
<br>device.type: ups
<br><a href="http://driver.name">driver.name</a>: nutdrv_qx
<br>driver.parameter.pollfreq: 30
<br>driver.parameter.pollinterval: 2
<br>driver.parameter.port: auto
<br>driver.parameter.productid: 0003
<br>driver.parameter.runtimecal: 450,32,1700,10
<br>driver.parameter.synchronous: no
<br>driver.parameter.vendorid: 06da
<br>driver.version: 2.7.4-151-g9209e18
<br>driver.version.data: Q1 0.07
<br>driver.version.internal: 0.28
<br>input.frequency: 60.1
<br>input.voltage: 122.3
<br>input.voltage.fault: 122.0
<br>output.voltage: 122.3
<br>ups.beeper.status: enabled
<br>ups.delay.shutdown: 30
<br>ups.delay.start: 180
<br>ups.load: 0
<br>ups.productid: 0003
<br>ups.status: OL
<br>ups.type: offline / line interactive
<br>ups.vendorid: 06da<br></span></div><div><span style="font-family:monospace"><br></span></div><div><span style="font-family:monospace"><br></span></div><div><span style="font-family:monospace">Thank you in advance for any corrections to my understanding of the documentation.</span></div></div>