<ol class="synline" style="LIST-STYLE-TYPE: decimal">
<li class="synline"><pre>[2009/01/07 18:20:50] <test3s> so I am running debian 5.0 2.6.26-1-686 kernel. I have an LVM logical volume that lvdisplay shows is 3.22 TB called /dev/volgroup00/vol01. When I try to mke2fs -j /dev/volgroup00/vol01, I get "mke2fs: Device size reported to be zero. Invalid partition specified, or partition table wasn't reread after running fdisk, due to a modified partition being busy and in use. You may need to reboot to re-read your partition table."</pre>
</li>
<li class="synline"><pre>[2009/01/07 18:23:33] <dutchfish> test3s, delve into pvcreate vgcreate and then you can create with lvcreate</pre></li>
<li class="synline"><pre>[2009/01/07 18:24:19] <dutchfish> test3s, after that you can install your FS</pre></li>
<li class="synline"><pre>[2009/01/07 18:25:46] <test3s> dutchfish: I already have a logical volume /dev/volgroup00/vol01 - shouldn't I be able to mke2fs -j /dev/volgroup00/vol01 ?</pre></li>
<li class="synline"><pre>[2009/01/07 18:26:06] <dutchfish> test3s, no</pre></li>
<li class="synline"><pre>[2009/01/07 18:26:34] <dutchfish> test3s, phys vol, vol group, logocal volume, FS in that order</pre></li>
<li class="synline"><pre>[2009/01/07 18:28:16] <dutchfish> test3s, <a href="http://www.debian-administration.org/articles/410">http://www.debian-administration.org/articles/410</a></pre></li>
<li class="synline"><pre>[2009/01/07 18:32:12] <test3s> dutchfish: I already went through that link - my volume group (found via vgscan) is volgroup00. my physical volume (found via pvdisplay) is /dev/cciss/c0d1p5, and is in volume group volgroup00. my logical volume (found via lvdisplay) is /dev/volgroup00/vol01. I don't understand...</pre>
</li>
<li class="synline"><pre>[2009/01/07 18:33:02] <dutchfish> test3s, normally you work through the mapper, so can you paste to pastebin th eoutput of vgdisplay and lvdisplay please?</pre></li>
<li class="synline"><pre>[2009/01/07 18:45:03] <test3s> when I do: lvcreate -n storage -l 100%FREE volgroup00, I get "device-mapper: reload ioctl failed: Invalid argument Aborting. Failed to activate new LV to wipe the start of it."</pre>
</li>
<li class="synline"><pre>[2009/01/07 18:46:15] <test3s> it's as if debian or my raid controller can't handle creating a 3TB logical volume</pre></li>
<li class="synline"><pre>[2009/01/07 18:47:53] <dutchfish> test3s, using etch or lenny?</pre></li>
<li class="synline"><pre>[2009/01/07 18:50:36] <dutchfish> test3s, i believe the max size of a single lvm partition in Etch is 16TB on 32 bit systems</pre></li>
<li class="synline"><pre>[2009/01/07 18:52:03] <dutchfish> test3s, can you post your lvdisplay vgdisplay? /msf dpkg pastebin</pre></li>
<li class="synline"><pre>[2009/01/07 18:52:18] <dutchfish> test3s, er: /msg dpkg pastebin</pre></li>
<li class="synline"><pre>[2009/01/07 18:58:32] <test3s> dutchfish: <a href="http://paste.debian.net/25493/">http://paste.debian.net/25493/</a></pre></li>
<li class="synline"><pre>[2009/01/07 19:01:48] <dutchfish> test3s, did you try to remove th elv and then create it again?</pre></li>
<li class="synline"><pre>[2009/01/07 19:02:57] <dutchfish> test3s, it looks like during creating the 1st LV, something went bad</pre></li>
<li class="synline"><pre>[2009/01/07 19:06:16] <test3s> dutchfish: <a href="http://paste.debian.net/25494/">http://paste.debian.net/25494/</a></pre></li>
<li class="synline"><pre>[2009/01/07 19:07:13] <dutchfish> test3s, how many disks? and how are they connected through controllers?</pre></li>
<li class="synline"><pre>[2009/01/07 19:09:58] <dutchfish> test3s, oh wait. Did you edit the partition table AFTER creating the physical volume?</pre></li>
<li class="synline"><pre>[2009/01/07 19:10:10] <test3s> dutchfish: 5 SATA disks attached to a single HP SmartArray E200 controller.</pre></li>
<li class="synline"><pre>[2009/01/07 19:10:20] <dutchfish> test3s, ok</pre></li>
<li class="synline"><pre>[2009/01/07 19:10:30] <folken> test3s: let me guess an ml-110? :)</pre></li>
<li class="synline"><pre>[2009/01/07 19:10:45] <test3s> folken: not sure.</pre></li>
<li class="synline"><pre>[2009/01/07 19:14:15] <dutchfish> test3s, did you take a close look at dmesg output? this could be hardware related, and what kernel are you running?</pre></li>
<li class="synline"><pre>[2009/01/07 19:14:58] <dutchfish> test3s, its not lvm2 it candle handle much bigger setups hands down</pre></li>
<li class="synline"><pre>[2009/01/07 19:17:16] <test3s> I am running debian 5.0 with 2.6.26-1-686 kernel.</pre></li>
<li class="synline"><pre>[2009/01/07 19:18:29] <dutchfish> test3s, i suspect its not a lvm2 nor kernel issue but the driver, could you take a look at dmesg output?</pre></li>
<li class="synline"><pre>[2009/01/07 19:18:29] <test3s> dmesg shows "device-mapper: table: device 104:21 too small for target" and "device-mapper: table: 254:1: linear: dm-linear: Device lookup failed"</pre>
</li>
<li class="synline"><pre>[ 1983.464417] device-mapper: table: device 104:21 too small for target</pre></li>
<li class="synline"><pre>[ 1983.464417] device-mapper: table: 254:1: linear: dm-linear: Device lookup failed </pre></li>
<li class="synline"><pre>[2009/01/07 19:19:03] <dutchfish> test3s, there is your problem, solving it is another thing</pre></li>
<li class="synline"><pre>[2009/01/07 19:19:12] <test3s> that error msg is displayed once for every time I tried and failed to create a logical volume past 1.25 TB or so.</pre></li>
<li class="synline"><pre>[2009/01/07 19:19:35] <dutchfish> test3s, right</pre></li>
<li class="synline"><pre>[2009/01/07 19:21:15] <dutchfish> test3s, Is it possible that you are using the wrong target type, e.g. RAID0/1/5?</pre></li>
<li class="synline"><pre>[2009/01/07 19:21:55] <dutchfish> test3s, cat /proc/mdstat would reveal that</pre></li>
<li class="synline"><pre>[2009/01/07 19:27:11] <test3s> dutchfish: ~# cat /proc/mdstat: cat: /proc/mdstat: No such file or directory</pre></li></ol>