Bug#452685: rt2x00-source: DWL-G122 Ver. B1 USB Stick doesn't work with new version.

[Andreas Juch]

Package: rt2x00-source
Version: 2.0.12+git20071103-1
Severity: important

Hi!

My usb wlan stick doesn't work with the new rt2x00-source version.
lsusb says:
Bus 006 Device 003: ID 2001:3c00 D-Link Corp. [hex] DWL-G122 802.11g rev. B1 [ralink]

With old version:
ii  rt2x00-modules-2.6.23.8           2.0.9-2+2.6.23.8-10.00.Custom

dmesg:
usb 1-4: new high speed USB device using ehci_hcd and address 3
usb 1-4: configuration #1 chosen from 1 choice
phy0 -> rt2500usb_validate_eeprom: EEPROM recovery - NIC: 0xfff0
phy0 -> rt2x00_set_chip: Info - Chipset detected - rt: 1201, rf: 0005, rev: 00000003.
wmaster0: Selected rate control algorithm 'simple'
usbcore: registered new interface driver rt2500usb
usbcore: registered new interface driver rt2570
phy0 -> rt2500usb_init_bbp: Debug - Start initialization from EEPROM...
phy0 -> rt2500usb_init_bbp: Debug - BBP: 0x11, value: 0x2b.
phy0 -> rt2500usb_init_bbp: Debug - BBP: 0x15, value: 0x18.
phy0 -> rt2500usb_init_bbp: Debug - BBP: 0x16, value: 0x18.
phy0 -> rt2500usb_init_bbp: Debug - BBP: 0x3e, value: 0x00.
phy0 -> rt2500usb_init_bbp: Debug - ...End initialization from EEPROM.
ADDRCONF(NETDEV_UP): wlan0: link is not ready
phy0 -> rt2x00mac_conf_tx: Info - Configured TX ring 0 - CWmin: 4, CWmax: 10, Aifs: 2.
phy0 -> rt2x00mac_conf_tx: Info - Configured TX ring 1 - CWmin: 4, CWmax: 10, Aifs: 2.
phy0 -> rt2x00mac_conf_tx: Info - Configured TX ring 7 - CWmin: 5, CWmax: 10, Aifs: 2.

$ lsmod | grep rt
rt2570                219008  0 
rt2500usb              30016  0 
rt2x00usb              15296  1 rt2500usb
rt2x00lib              31488  2 rt2500usb,rt2x00usb
crc_itu_t               4608  1 rt2x00lib
mac80211              151236  3 rc80211_simple,rt2x00usb,rt2x00lib
parport_pc             42472  0 
parport                45132  3 ppdev,parport_pc,lp
firmware_class         13632  2 rt2x00lib,dvb_ttpci

Link led is active, Act led blinks sometimes.


With new version (new modules installed, rebooted, plugged the stick in):
ii  rt2x00-modules-2.6.23.8           2.0.12+git20071103-1+2.6.23.8-10.

lsmod | grep rt
rt2570                219008  0 
rt2500usb              30784  0 
rt2x00usb              16448  1 rt2500usb
rt2x00lib              33792  2 rt2500usb,rt2x00usb
crc_itu_t               4608  1 rt2x00lib
mac80211              151236  2 rt2x00usb,rt2x00lib
parport_pc             42472  0 
parport                45132  3 ppdev,parport_pc,lp
firmware_class         13632  2 rt2x00lib,dvb_ttpci

dmesg:
usb 6-4: new high speed USB device using ehci_hcd and address 3
usb 6-4: configuration #1 chosen from 1 choice
phy0 -> rt2500usb_validate_eeprom: EEPROM recovery - NIC: 0xfff0
phy0 -> rt2x00_set_chip: Info - Chipset detected - rt: 1201, rf: 0005, rev: 00000003.
phy0 -> rt2500usb_init_eeprom: Error - Invalid RT chipset detected.
phy0 -> rt2x00lib_probe_dev: Error - Failed to allocate device.
usbcore: registered new interface driver rt2500usb
idVendor = 0x2001, idProduct = 0x3c00 
usbcore: registered new interface driver rt2570

The stick doesn't show any activity, no leds are active, network-manager doesn't show anything wireless, ifconfig shows just the ethernet and lo device. Even with the old rt2x00-source version i wasn't able to connect to my WPA-Wlan, but the new version is IMO a step backwards, as there is no activity at all.

-- System Information:
Debian Release: lenny/sid
  APT prefers testing
  APT policy: (600, 'testing'), (500, 'unstable')
Architecture: amd64 (x86_64)

Kernel: Linux 2.6.23.8 (SMP w/2 CPU cores)
Locale: LANG=de_AT.UTF-8, LC_CTYPE=de_AT.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash

Versions of packages rt2x00-source depends on:
ii  bzip2                         1.0.3-7    high-quality block-sorting file co
ii  debhelper                     5.0.60     helper programs for debian/rules
ii  module-assistant              0.10.11    tool to make module package creati

rt2x00-source recommends no packages.

-- no debconf information