[sane-devel] HP ScanJet 6100C Configuration

[Frank Roberts - SOTL]

Thanks for the help Peter.

I did the following.
1. Changed /dev/scanner to /dev/sg0
2. Made directory sane.d-bak
3. removed all configuration files from sane.d except hp.conf
4 as root did chmood 666 /dev/sg0

From this I would be happy to report glad tidings but alas this is not so. 
Status: O

I received exactly the same results - no change.

Thanks
Frank

On Sunday 04 August 2002 04:06, Peter Kirchgessner wrote:
> Hi Frank,
>
> try the hp.conf with
>
> scsi HP
> /dev/sg0
>
> If this does not work, you may have a second hp.conf at
> /etc/sane.d/hp.conf. Try that one with the same content.
> If it still does not work, do as root a
>
> chmod 666 /dev/sg0
>
> and try it again.
>
> Sincerely
>
> Peter
>
> Frank Roberts - SOTL wrote:
> > Hi All:
> >
> > I hope You people will have time to help a relative novice with
> > configuration of an HP 6100 C which is to be used intermidently on 2
> > different RH 7.3 systems.
> >
> >
> > As stated previously the scanner is an HP 6100C if I issue the command:
> > The scanner is connected by 40 pin scsi.
> > Several commands were issues with the following results:
> >
> > $ scanimage --list devices
> > sg0     HP C2520A 36644
> > sg1     Mitsumi    CD-R
> > sg2     Soney      CD-RW
> >
> >
> > $ cat /proc/scsi/scsa
> > Attached devices:
> > Host: scsi0 Channel: 00 Id: 04 Lun: 00 Vendor: HP Model: C2520A Rev: 3644
> > Type: Processor ANSI SCSI revision: 02
> > Host: scsi1 Channel: 00 Id: 00 Lun: 00 Vendor: MITSUMI Model: CD-ROM
> > FX4830T!B Rev: R02C Type: CD-ROM ANSI SCSI revision: 02
> > Host: scsi1 Channel: 00 Id: 01 Lun: 00 Vendor: SONY Model: CD-RW CRX175E2
> > Rev: S002 Type: CD-ROM ANSI SCSI revision: 02
> >
> >
> > $ export   SANE_DEBUGG_HP=17
> > $ scanimage -L
> > [scanei_debug] Setting debug level of hp to 17
> > [hp] sane_init called[hp]
> > [hp] sane_init will finish with Success
> > [hp] sane_get_devices called
> > [hp] hp_read_config: hp backend v0.95 start reading conf file
> > [hp] hp_read_config: processing line <scsi HP>
> > [hp] hp_read_config: processing line </dev/scaner>
> > [hp] hp_read_config: attach scsi HP
> > [hp] hp_read_config: attach /dev/scanner
> > [hp] hp_get_dev: New device /dev/scanner, connect-scsi, scsi-request=1
> > [hp] sanei_hp_device_new: /dev/scanner
> > [hp] scsi_newopen failed (Invalid argument)
> > [hp] /dev/scanner: Can't open scsi device
> > [hp] sane_get_devices will finish with Success
> > [hp] sane_exit called
> > [hp] sane_exit will finish
> >
> >
> > The sane configuration file /etc/sane.d/ho.conf is as follows:
> > scsi HP
> > /dev/scannet
> >
> > I would appreciate any advice you people may be able to offer.
> >
> > Thanks
> > Frank
> >
> > Thanks
> >
> >
> >
> > _______________________________________________
> > Sane-devel mailing list
> > Sane-devel@www.mostang.com
> > http://www.mostang.com/mailman/listinfo/sane-devel