[sane-devel] FW: Sus3 7.3, Sane 1.05, HP5300C

Art Fore art_fore at 3mts.com
Mon Feb 18 10:19:43 GMT 2002


How do you set SANE_SG_BUFFERSIZE? I done a SANE_SG_BUFFERSIZE=32768, but
this does not seem to do anything? Also, how do you tell which it is using,
scanner.o or hp5300.o? Is this in a config file somewhere?

Art

-----Original Message-----
From: Jeremy Hall [mailto:jhall at UU.NET]
Sent: Monday, February 18, 2002 2:16 PM
To: art_fore at 3mts.com
Cc: sane-devel at mostang.com
Subject: Re: [sane-devel] FW: Sus3 7.3, Sane 1.05, HP5300C


THe 5300 doesn't use scanner.o, it uses hp5300.o (or whatever it was
called) It's basically a modified microtek driver.

Make sure your SANE_SG_BUFFERSIZE is set correctly, if memory serves, this
should be 32768 (this is an environment variable) then somewhere in sane's
configuration options is a directive that tells sane to use a driver, make
sure it is using the avision driver.

This was with sane 1.0.3, but things still should work?

_J

In the new year, Art Fore wrote:
> I have gone through the whole exercise again, still no results except that
> now the cat /dev/scsi/scsi does not work. When from bad to worse.
>
> Does anyone have a howto to install this scanner in Suse 7.3, 2.4.17
kernel,
> 1.05 sane drivers?
>
> Or, what about the 1.06 sane drivers, I installed them but then
> sane-find-scanner and scanimage don't work at all, command not found, so
> went back to 1.05.
>
> Scanner shows up under scsi in yast2 hardware, lsmod shows scanner unused,
> so I am confused.
>
> Art
>
> -----Original Message-----
> From: Art Fore [mailto:art_fore at 3mts.com]
> Sent: Sunday, February 17, 2002 10:45 AM
> To: sane-devel at www.mostang.com
> Subject: Sus3 7.3, Sane 1.05, HP5300C
>
>
> I have tried everthing that I could find but have no success. Have
> configured scanner in Yast2 with Avision. Here is what I get
>
> sane-find-scanner
> found scanner "HP ScanJet 5300C 4.00" at /dev/sg1
>
> scanimage -L results in no scanners were identified.
>
> I edited the dll.conf and removed the # from the avision.
>
> Still nothing.
>
> I unistalled sane 1.05 and installed 1.06 backend and frontend, but then
> sane-find-scanner and scanimage comes up with command not found, so I
> uninstalled and reinstalled the 1.05 from the Suse CD.
>
> Still nothing, other than the /dev/sg0 changed to /dev/sg1. Generic scsi
is
> compiled in kernel, HP53xx USB is compled as module. Had it the other way
> around, but there was no change.
>
> Did not try the patch as it seemed to be for 1.04 and I am running 1.05
and
> figured it would screw something up more than it already is.
>
> Would appreciate any help.
>
> Art
>
>
> _______________________________________________
> Sane-devel mailing list
> Sane-devel at www.mostang.com
> http://www.mostang.com/mailman/listinfo/sane-devel
>





More information about the sane-devel mailing list