[sane-devel] HP question? and Microtek

[T. Martin]

Hello, 
I'm running sane 1.0.6 I have two scanners hooked up for testing. 
HP 5p I think it might be a hardware issue. The light comes on for a
second then goes out. the carriage starts moving as to scan but only moves
1/2 inch then trys to retreat as if done and goes to clicking as to drive
belt slips.
Second is the MIcrotek Scanmaker II
with xscanimage it can do a color preview but when it comes to scanning
color it starts and completes the red pass but then errors out.
with sane_start: Error during device I/O
Following is a excerpt from the error.log I compiled. 

The system is as follows. 
Vector Linux (based on slack)
glibc= libc-2.2.3
gcc version 2.95.3 20010315 (release)
Linux ppro 2.4.5 #5 Sun Jun 24 13:44:21 UTC 2001 i686 GenuineIntel
all gui stuff stuff is exports X 4.1.0
Thanks 
Terry


[microtek] sane_get_parameters...
[microtek] sane_get_parameters:  regular 3-pass color
[microtek] sane_get_parameters:  res_code = 33 (21)
[microtek] sane_get_parameters:  dots_per_mm:  3.937008
[microtek] sane_get_parameters:  units_per_mm:  11.811024
[microtek] WIDTHPIX:  before exp: 448
[microtek] sane_get_parameters:  lines: 659  ppl: 448  bpl: 448
[microtek] set_pass_parameters:  three-pass, on 2
[microtek] .wait_ready 8...
[microtek] SENSE!  fd = 8
[microtek] sense = 00 00 00 00.
[microtek] finagle_precal...
[microtek] .scanning_frame...
[microtek] .scanning_frame:  in- 21,35  1369,2012
[microtek] .scanning_frame: out- 21,35  1369,2012
[microtek] SENSE!  fd = 8
[microtek] sense = 00 00 00 00.
[microtek] .accessory...
[microtek] SENSE!  fd = 8
[microtek] sense = 00 00 00 00.
[microtek] .download_gamma...
[microtek] .download_gamma:  256 entries of 1 bytes, max 255
[microtek] .download_gamma: by default
[microtek] SENSE!  fd = 8
[microtek] sense = 00 00 00 00.
[microtek] .mode_select 8...
[microtek] .mode_select:  pap_len: 4199
[microtek] SENSE!  fd = 8
[microtek] sense = 00 00 00 00.
[microtek] .wait_ready 8...
[microtek] SENSE!  fd = 8
[microtek] sense = 00 00 00 00.
[microtek] .start_scan...
[microtek] SENSE!  fd = 8
[microtek] sense = 00 00 00 00.
[microtek] .get_scan_status 8...
[microtek] SENSE!  fd = 8
[microtek] sense = 00 00 00 00.
[microtek] get_scan_status(6): 139, 1825, 65543  -> #0
[microtek] > 8b 21  7  7  0  1
[microtek] get_scan_status:  busy, retry in 5...
[microtek] SENSE!  fd = 8
[microtek] sense = 00 00 00 00.
[microtek] get_scan_status(6): 139, 1825, 65543  -> #1
[microtek] > 8b 21  7  7  0  1
[microtek] get_scan_status:  busy, retry in 10...
[microtek] SENSE!  fd = 8
[microtek] sense = 00 00 00 00.
[microtek] get_scan_status(6): 139, 1825, 65543  -> #2
[microtek] > 8b 21  7  7  0  1
[microtek] get_scan_status:  busy, retry in 15...
[microtek] SENSE!  fd = 8
[microtek] sense = 00 00 00 00.
[microtek] get_scan_status(6): 139, 1825, 65543  -> #3
[microtek] > 8b 21  7  7  0  1
[microtek] get_scan_status:  busy, retry in 20...
[microtek] sane_start:  get_scan_status fails
[microtek] end_scan...
[microtek] .stop_scan...