[sane-devel] Problem with HP ScanJet 4p and SCSI
David Brant
brantosaurus at hotmail.com
Sun May 10 15:16:50 UTC 2009
Hello
I have a problem connecting a Hewlet Packard ScanJet 4p by scsi. Scanner
is connected to the computer with the scsi cable and switched on. All i
get is "No devices available' using Xsane 0.995
Computer is Dell Optiplex running Ubuntu 8.10 Intrepid Ibex, Linux
kernel version 2.6.27-11-generic and GNOME 2.24.1
The SCSI card is an Adaptec AVA-2904 PCI-to-Fast SCSI Host Adapter
(AIC-7800 Family)
According to the SANE Supported Devices List, the combination is
'completely' supported with the sane-hp manual backend. I have tried to
manually install it, by installing libsane-extras and
editing /etc/sane.d/dll.conf, but i see the "hp" reference to the SANE
dynamic backend loader is already active
-------------------------------------------------------------------------------start
# /etc/sane.d/dll.conf - Configuration file for the SANE dynamic backend
loader
#
# On Debian systems, the dll backend will also look for pieces of
configuration
# in the /etc/sane.d/dll.d directory -- packages providing backends
should drop
# a config file similar to dll.conf in this directory.
#
# enable the next line if you want to allow access through the network:
gt68xx
hp
hp3900
hpsj5s
hp3500
hp4200
hp5400
hp5590
hpljm1005
hs2p
ibm
-------------------------------------------------------------------------------end
Scsi card (lspci -v):
-------------------------------------------------------------------------------start
00:0d.0 SCSI storage controller: Adaptec AIC-7850 (rev 03)
Subsystem: Adaptec Device 7850
Flags: bus master, medium devsel, latency 64, IRQ 11
I/O ports at c800 [disabled] [size=256]
Memory at ff000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: aic7xxx
Kernel modules: aic7xxx
-------------------------------------------------------------------------------end
A little more testing from the web (udevinfo -a
-p /sys/class/scsi_generic/sg2)
-------------------------------------------------------------------------------start
Udevinfo starts with the device specified by the devpath and then
walks up the chain of parent devices. It prints for every device
found, all possible attributes in the udev rules key format.
A rule to match, can be composed by the attributes of the device
and the attributes from one single parent device.
looking at device
'/devices/pci0000:00/0000:00:0d.0/host2/target2:0:2/2:0:2:0/scsi_generic/sg2':
KERNEL=="sg2"
SUBSYSTEM=="scsi_generic"
DRIVER==""
looking at parent device
'/devices/pci0000:00/0000:00:0d.0/host2/target2:0:2/2:0:2:0/scsi_generic':
KERNELS=="scsi_generic"
SUBSYSTEMS==""
DRIVERS==""
looking at parent device
'/devices/pci0000:00/0000:00:0d.0/host2/target2:0:2/2:0:2:0':
KERNELS=="2:0:2:0"
SUBSYSTEMS=="scsi"
DRIVERS==""
ATTRS{device_blocked}=="0"
ATTRS{type}=="3"
ATTRS{scsi_level}=="3"
ATTRS{vendor}=="HP "
ATTRS{model}=="C1130A "
ATTRS{rev}=="3614"
ATTRS{state}=="running"
ATTRS{timeout}=="0"
ATTRS{iocounterbits}=="32"
ATTRS{iorequest_cnt}=="0x1406"
ATTRS{iodone_cnt}=="0x1406"
ATTRS{ioerr_cnt}=="0x1"
ATTRS{modalias}=="scsi:t-0x03"
ATTRS{evt_media_change}=="0"
ATTRS{queue_depth}=="2"
ATTRS{queue_type}=="none"
looking at parent device
'/devices/pci0000:00/0000:00:0d.0/host2/target2:0:2':
KERNELS=="target2:0:2"
SUBSYSTEMS=="scsi"
DRIVERS==""
looking at parent device '/devices/pci0000:00/0000:00:0d.0/host2':
KERNELS=="host2"
SUBSYSTEMS=="scsi"
DRIVERS==""
looking at parent device '/devices/pci0000:00/0000:00:0d.0':
KERNELS=="0000:00:0d.0"
SUBSYSTEMS=="pci"
DRIVERS=="aic7xxx"
ATTRS{vendor}=="0x9004"
ATTRS{device}=="0x5078"
ATTRS{subsystem_vendor}=="0x9004"
ATTRS{subsystem_device}=="0x7850"
ATTRS{class}=="0x010000"
ATTRS{irq}=="11"
ATTRS{local_cpus}=="ffffffff,ffffffff"
ATTRS{local_cpulist}=="0-63"
ATTRS{modalias}=="pci:v00009004d00005078sv00009004sd00007850bc01sc00i00"
ATTRS{broken_parity_status}=="0"
ATTRS{msi_bus}==""
looking at parent device '/devices/pci0000:00':
KERNELS=="pci0000:00"
SUBSYSTEMS==""
DRIVERS==""
-------------------------------------------------------------------------------end
and (cat /proc/scsi/scsi)
-------------------------------------------------------------------------------start
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: ATA Model: IBM-DTTA-371010 Rev: T77O
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi1 Channel: 00 Id: 00 Lun: 00
Vendor: SONY Model: CD-ROM CDU701 Rev: 1.0f
Type: CD-ROM ANSI SCSI revision: 05
Host: scsi2 Channel: 00 Id: 02 Lun: 00
Vendor: HP Model: C1130A Rev: 3614
Type: Processor ANSI SCSI revision: 02
-------------------------------------------------------------------------------end
My scanner is set to address 2 which is correctly detected.
Scanner is recognised by the computer (kern.log):
-------------------------------------------------------------------------------start
May 10 15:22:39 david-desktop kernel:
Inspecting /boot/System.map-2.6.27-11-generic
May 10 15:22:39 david-desktop kernel: Cannot find map file.
May 10 15:22:39 david-desktop kernel: Loaded 47311 symbols from 77
modules.
May 10 15:22:39 david-desktop kernel: [ 3.548981] SCSI subsystem
initialized
May 10 15:22:39 david-desktop kernel: [ 3.700451] usbcore: registered
new interface driver usbfs
May 10 15:22:39 david-desktop kernel: [ 3.700523] usbcore: registered
new interface driver hub
May 10 15:22:39 david-desktop kernel: [ 3.733107] usbcore: registered
new device driver usb
May 10 15:22:39 david-desktop kernel: [ 3.799951] PCI: setting IRQ 11
as level-triggered
May 10 15:22:39 david-desktop kernel: [ 3.799963] aic7xxx
0000:00:0d.0: found PCI INT A -> IRQ 11
May 10 15:22:39 david-desktop kernel: [ 3.799997] aic7xxx
0000:00:0d.0: sharing IRQ 11 with 0000:00:0e.2
May 10 15:22:39 david-desktop kernel: [ 3.801229] ahc_pci:0:13:0:
Host Adapter Bios disabled. Using default SCSI device parameters
May 10 15:22:39 david-desktop kernel: [ 3.850073] 8139cp: 10/100 PCI
Ethernet driver v1.3 (Mar 22, 2004)
May 10 15:22:39 david-desktop kernel: [ 3.861711] libata version 3.00
loaded.
May 10 15:22:39 david-desktop kernel: [ 3.863951] USB Universal Host
Controller Interface driver v3.0
May 10 15:22:39 david-desktop kernel: [ 3.916942] Warning! ehci_hcd
should always be loaded before uhci_hcd and ohci_hcd, not after
May 10 15:22:39 david-desktop kernel: [ 18.816959] scsi0 : Adaptec
AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
May 10 15:22:39 david-desktop kernel: [ 18.816964] <Adaptec
2902/04/10/15/20C/30C SCSI adapter>
May 10 15:22:39 david-desktop kernel: [ 18.816968] aic7850:
Single Channel A, SCSI Id=7, 3/253 SCBs
May 10 15:22:39 david-desktop kernel: [ 18.816971]
May 10 15:22:39 david-desktop kernel: [ 18.820790] ata_piix
0000:00:07.1: version 2.12
May 10 15:22:39 david-desktop kernel: [ 18.821300] scsi1 : ata_piix
May 10 15:22:39 david-desktop kernel: [ 18.822339] scsi2 : ata_piix
May 10 15:22:39 david-desktop kernel: [ 18.822516] ata1: PATA max
UDMA/33 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
May 10 15:22:39 david-desktop kernel: [ 18.822524] ata2: PATA max
UDMA/33 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
May 10 15:22:39 david-desktop kernel: [ 19.007021] ata1.00: ATA-4:
IBM-DTTA-371010, T77OA73A, max UDMA/33
May 10 15:22:39 david-desktop kernel: [ 19.007033] ata1.00: 19746720
sectors, multi 8: LBA
May 10 15:22:39 david-desktop kernel: [ 19.057032] ata1.00: configured
for UDMA/33
May 10 15:22:39 david-desktop kernel: [ 19.221279] ata2.00: ATAPI:
CD-ROM CDU701, 1.0f, max MWDMA2
May 10 15:22:39 david-desktop kernel: [ 19.237175] ata2.00: configured
for MWDMA2
May 10 15:22:39 david-desktop kernel: [ 19.237227] scsi: waiting for
bus probes to complete ...
May 10 15:22:39 david-desktop kernel: [ 19.348698] scsi 0:0:2:0:
Processor HP C1130A 3614 PQ: 0 ANSI: 2
May 10 15:22:39 david-desktop kernel: [ 19.348756] scsi target0:0:2:
Beginning Domain Validation
May 10 15:22:39 david-desktop kernel: [ 19.356661] scsi target0:0:2:
Ending Domain Validation
May 10 15:22:39 david-desktop kernel: [ 20.411822] scsi 1:0:0:0:
Direct-Access ATA IBM-DTTA-371010 T77O PQ: 0 ANSI: 5
May 10 15:22:39 david-desktop kernel: [ 20.415231] scsi 2:0:0:0:
CD-ROM SONY CD-ROM CDU701 1.0f PQ: 0 ANSI: 5
May 10 15:22:39 david-desktop kernel: [ 20.415540] uhci_hcd
0000:00:07.2: found PCI INT D -> IRQ 11
May 10 15:22:39 david-desktop kernel: [ 20.415574] uhci_hcd
0000:00:07.2: sharing IRQ 11 with 0000:00:0e.1
May 10 15:22:39 david-desktop kernel: [ 20.415610] uhci_hcd
0000:00:07.2: UHCI Host Controller
May 10 15:22:39 david-desktop kernel: [ 20.415734] uhci_hcd
0000:00:07.2: new USB bus registered, assigned bus number 1
May 10 15:22:39 david-desktop kernel: [ 20.415778] uhci_hcd
0000:00:07.2: irq 11, io base 0x0000cce0
May 10 15:22:39 david-desktop kernel: [ 20.416282] usb usb1:
configuration #1 chosen from 1 choice
May 10 15:22:39 david-desktop kernel: [ 20.416360] hub 1-0:1.0: USB
hub found
May 10 15:22:39 david-desktop kernel: [ 20.416390] hub 1-0:1.0: 2
ports detected
May 10 15:22:39 david-desktop kernel: [ 20.524729] PCI: setting IRQ 10
as level-triggered
May 10 15:22:39 david-desktop kernel: [ 20.524741] uhci_hcd
0000:00:0e.0: found PCI INT A -> IRQ 10
May 10 15:22:39 david-desktop kernel: [ 20.524780] uhci_hcd
0000:00:0e.0: sharing IRQ 10 with 0000:00:0e.3
May 10 15:22:39 david-desktop kernel: [ 20.524811] uhci_hcd
0000:00:0e.0: UHCI Host Controller
May 10 15:22:39 david-desktop kernel: [ 20.524939] uhci_hcd
0000:00:0e.0: new USB bus registered, assigned bus number 2
May 10 15:22:39 david-desktop kernel: [ 20.524983] uhci_hcd
0000:00:0e.0: irq 10, io base 0x0000ccc0
May 10 15:22:39 david-desktop kernel: [ 20.525533] usb usb2:
configuration #1 chosen from 1 choice
May 10 15:22:39 david-desktop kernel: [ 20.525611] hub 2-0:1.0: USB
hub found
May 10 15:22:39 david-desktop kernel: [ 20.525639] hub 2-0:1.0: 2
ports detected
May 10 15:22:39 david-desktop kernel: [ 20.556838] scsi 0:0:2:0:
Attached scsi generic sg0 type 3
May 10 15:22:39 david-desktop kernel: [ 20.556944] scsi 1:0:0:0:
Attached scsi generic sg1 type 0
May 10 15:22:39 david-desktop kernel: [ 20.557093] scsi 2:0:0:0:
Attached scsi generic sg2 type 5
May 10 15:22:39 david-desktop kernel: [ 20.609976] Driver 'sr' needs
updating - please use bus_type methods
May 10 15:22:39 david-desktop kernel: [ 20.615417] sr0: scsi3-mmc
drive: 14x/14x cd/rw xa/form2 cdda tray
May 10 15:22:39 david-desktop kernel: [ 20.615430] Uniform CD-ROM
driver Revision: 3.20
May 10 15:22:39 david-desktop kernel: [ 20.615688] sr 2:0:0:0:
Attached scsi CD-ROM sr0
May 10 15:22:39 david-desktop kernel: [ 20.733700] uhci_hcd
0000:00:0e.1: found PCI INT B -> IRQ 11
May 10 15:22:39 david-desktop kernel: [ 20.733726] uhci_hcd
0000:00:0e.1: sharing IRQ 11 with 0000:00:07.2
May 10 15:22:39 david-desktop kernel: [ 20.733775] uhci_hcd
0000:00:0e.1: UHCI Host Controller
May 10 15:22:39 david-desktop kernel: [ 20.733843] uhci_hcd
0000:00:0e.1: new USB bus registered, assigned bus number 3
May 10 15:22:39 david-desktop kernel: [ 20.733884] uhci_hcd
0000:00:0e.1: irq 11, io base 0x0000cca0
May 10 15:22:39 david-desktop kernel: [ 20.734235] usb usb3:
configuration #1 chosen from 1 choice
May 10 15:22:39 david-desktop kernel: [ 20.734311] hub 3-0:1.0: USB
hub found
May 10 15:22:39 david-desktop kernel: [ 20.734339] hub 3-0:1.0: 2
ports detected
May 10 15:22:39 david-desktop kernel: [ 20.845044] usb 2-1: new full
speed USB device using uhci_hcd and address 2
May 10 15:22:39 david-desktop kernel: [ 20.942577] ehci_hcd
0000:00:0e.2: found PCI INT C -> IRQ 11
May 10 15:22:39 david-desktop kernel: [ 20.942609] ehci_hcd
0000:00:0e.2: sharing IRQ 11 with 0000:00:0d.0
May 10 15:22:39 david-desktop kernel: [ 20.942658] ehci_hcd
0000:00:0e.2: EHCI Host Controller
May 10 15:22:39 david-desktop kernel: [ 20.942730] ehci_hcd
0000:00:0e.2: new USB bus registered, assigned bus number 4
May 10 15:22:39 david-desktop kernel: [ 20.942827] ehci_hcd
0000:00:0e.2: irq 11, io mem 0xff001800
May 10 15:22:39 david-desktop kernel: [ 20.969066] ehci_hcd
0000:00:0e.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
May 10 15:22:39 david-desktop kernel: [ 20.970348] usb usb4:
configuration #1 chosen from 1 choice
May 10 15:22:39 david-desktop kernel: [ 20.970474] hub 4-0:1.0: USB
hub found
May 10 15:22:39 david-desktop kernel: [ 20.970505] hub 4-0:1.0: 4
ports detected
May 10 15:22:39 david-desktop kernel: [ 21.178666] ohci1394
0000:00:0e.3: found PCI INT A -> IRQ 10
May 10 15:22:39 david-desktop kernel: [ 21.178700] ohci1394
0000:00:0e.3: sharing IRQ 10 with 0000:00:0e.0
May 10 15:22:39 david-desktop kernel: [ 21.231697] ohci1394: fw-host0:
OHCI-1394 1.1 (PCI): IRQ=[10] MMIO=[ff001000-ff0017ff] Max
Packet=[2048] IR/IT contexts=[4/8]
May 10 15:22:39 david-desktop kernel: [ 21.241863] 8139cp
0000:02:09.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible
chip
May 10 15:22:39 david-desktop kernel: [ 21.241876] 8139cp
0000:02:09.0: Try the "8139too" driver instead.
May 10 15:22:39 david-desktop kernel: [ 21.263833] 8139too Fast
Ethernet driver 0.9.28
May 10 15:22:39 david-desktop kernel: [ 21.273707] PCI: setting IRQ 9
as level-triggered
May 10 15:22:39 david-desktop kernel: [ 21.273720] 8139too
0000:02:09.0: found PCI INT A -> IRQ 9
May 10 15:22:39 david-desktop kernel: [ 21.273761] 8139too
0000:02:09.0: sharing IRQ 9 with 0000:01:00.0
May 10 15:22:39 david-desktop kernel: [ 21.274938] eth0: RealTek
RTL8139 at 0xdc00, 00:50:bf:d8:b0:98, IRQ 9
May 10 15:22:39 david-desktop kernel: [ 21.274945] eth0: Identified
8139 chip type 'RTL-8139C'
May 10 15:22:39 david-desktop kernel: [ 21.365134] usb 2-1: device not
accepting address 2, error -71
May 10 15:22:39 david-desktop kernel: [ 21.421144] hub 2-0:1.0: unable
to enumerate USB device on port 1
May 10 15:22:39 david-desktop kernel: [ 21.534475] usb 4-1: new high
speed USB device using ehci_hcd and address 2
May 10 15:22:39 david-desktop kernel: [ 21.536838] Driver 'sd' needs
updating - please use bus_type methods
May 10 15:22:39 david-desktop kernel: [ 21.537277] sd 1:0:0:0: [sda]
19746720 512-byte hardware sectors (10110 MB)
May 10 15:22:39 david-desktop kernel: [ 21.537332] sd 1:0:0:0: [sda]
Write Protect is off
May 10 15:22:39 david-desktop kernel: [ 21.537339] sd 1:0:0:0: [sda]
Mode Sense: 00 3a 00 00
May 10 15:22:39 david-desktop kernel: [ 21.537410] sd 1:0:0:0: [sda]
Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
May 10 15:22:39 david-desktop kernel: [ 21.537605] sd 1:0:0:0: [sda]
19746720 512-byte hardware sectors (10110 MB)
May 10 15:22:39 david-desktop kernel: [ 21.537645] sd 1:0:0:0: [sda]
Write Protect is off
May 10 15:22:39 david-desktop kernel: [ 21.537652] sd 1:0:0:0: [sda]
Mode Sense: 00 3a 00 00
May 10 15:22:39 david-desktop kernel: [ 21.537729] sd 1:0:0:0: [sda]
Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
May 10 15:22:39 david-desktop kernel: [ 21.537741] sda: sda1 < sda5
sda6 sda7 >
May 10 15:22:39 david-desktop kernel: [ 21.580400] sd 1:0:0:0: [sda]
Attached SCSI disk
May 10 15:22:39 david-desktop kernel: [ 21.666023] usb 4-1:
configuration #1 chosen from 1 choice
May 10 15:22:39 david-desktop kernel: [ 21.666211] hub 4-1:1.0: USB
hub found
May 10 15:22:39 david-desktop kernel: [ 21.666362] hub 4-1:1.0: 4
ports detected
May 10 15:22:39 david-desktop kernel: [ 22.299037] PM: Starting manual
resume from disk
May 10 15:22:39 david-desktop kernel: [ 22.299052] PM: Resume from
partition 8:6
May 10 15:22:39 david-desktop kernel: [ 22.299056] PM: Checking
hibernation image.
May 10 15:22:39 david-desktop kernel: [ 22.299498] PM: Resume from
disk failed.
May 10 15:22:39 david-desktop kernel: [ 22.403516] kjournald starting.
Commit interval 5 seconds
May 10 15:22:39 david-desktop kernel: [ 22.403561] EXT3-fs: mounted
filesystem with ordered data mode.
May 10 15:22:39 david-desktop kernel: [ 22.513445] ieee1394: Host
added: ID:BUS[0-00:1023] GUID[0011066600010bbf]
May 10 15:22:39 david-desktop kernel: [ 35.098153] udevd version 124
started
May 10 15:22:39 david-desktop kernel: [ 36.978158] pci_hotplug: PCI
Hot Plug PCI Core version: 0.5
May 10 15:22:39 david-desktop kernel: [ 37.114771] Linux agpgart
interface v0.103
May 10 15:22:39 david-desktop kernel: [ 37.194494] shpchp: Standard
Hot Plug PCI Controller Driver version: 0.4
May 10 15:22:39 david-desktop kernel: [ 37.382252] agpgart-intel
0000:00:00.0: Intel 440BX Chipset
May 10 15:22:39 david-desktop kernel: [ 37.402422] agpgart-intel
0000:00:00.0: AGP aperture is 64M @ 0xf0000000
May 10 15:22:39 david-desktop kernel: [ 37.434314] piix4_smbus
0000:00:07.3: Host SMBus controller not enabled!
May 10 15:22:39 david-desktop kernel: [ 37.540104] request region #1
May 10 15:22:39 david-desktop kernel: [ 37.540131] isp1760: probe of
0000:00:07.3 failed with error -16
May 10 15:22:39 david-desktop kernel: [ 37.590402] input: PC Speaker
as /devices/platform/pcspkr/input/input2
May 10 15:22:39 david-desktop kernel: [ 38.998733] input: ImPS/2
Logitech Wheel Mouse as /devices/platform/i8042/serio1/input/input3
May 10 15:22:39 david-desktop kernel: [ 40.299826] dcdbas dcdbas: Dell
Systems Management Base Driver (version 5.6.0-3.2)
May 10 15:22:39 david-desktop kernel: [ 44.194645] parport_pc 00:03:
reported by Plug and Play BIOS
May 10 15:22:39 david-desktop kernel: [ 44.194765] parport0: PC-style
at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,EPP,ECP]
May 10 15:22:39 david-desktop kernel: [ 44.291494] lp0: using parport0
(interrupt-driven).
May 10 15:22:39 david-desktop kernel: [ 45.426178] cs4236_isapnp
01:01.00: activated
May 10 15:22:39 david-desktop kernel: [ 45.428746] cs4236_isapnp
01:01.02: activated
May 10 15:22:39 david-desktop kernel: [ 45.431316] cs4236_isapnp
01:01.03: activated
May 10 15:22:39 david-desktop kernel: [ 46.058396] Adding 787144k swap
on /dev/sda6. Priority:-1 extents:1 across:787144k
May 10 15:22:39 david-desktop kernel: [ 46.674104] EXT3 FS on sda5,
internal journal
May 10 15:22:39 david-desktop kernel: [ 47.787344] kjournald starting.
Commit interval 5 seconds
May 10 15:22:39 david-desktop kernel: [ 47.788712] EXT3 FS on sda7,
internal journal
May 10 15:22:39 david-desktop kernel: [ 47.788726] EXT3-fs: mounted
filesystem with ordered data mode.
May 10 15:22:39 david-desktop kernel: [ 48.279006] type=1505
audit(1241965356.480:2): operation="profile_load"
name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=3888
May 10 15:22:39 david-desktop kernel: [ 48.837903] type=1505
audit(1241965357.037:3): operation="profile_load"
name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=3893
May 10 15:22:39 david-desktop kernel: [ 48.839059] type=1505
audit(1241965357.041:4): operation="profile_load" name="/usr/sbin/cupsd"
name2="default" pid=3893
May 10 15:22:39 david-desktop kernel: [ 49.127008] ip_tables: (C)
2000-2006 Netfilter Core Team
May 10 15:22:39 david-desktop kernel: [ 50.576994] acpi_cpufreq:
Unknown symbol acpi_processor_notify_smm
May 10 15:22:39 david-desktop kernel: [ 50.577349] acpi_cpufreq:
Unknown symbol acpi_processor_unregister_performance
May 10 15:22:39 david-desktop kernel: [ 50.578856] acpi_cpufreq:
Unknown symbol acpi_processor_preregister_performance
May 10 15:22:39 david-desktop kernel: [ 50.579423] acpi_cpufreq:
Unknown symbol acpi_processor_register_performance
May 10 15:22:40 david-desktop kernel: [ 51.998493] warning:
`avahi-daemon' uses 32-bit capabilities (legacy support in use)
May 10 15:22:40 david-desktop kernel: [ 52.469202] apm: BIOS version
1.2 Flags 0x03 (Driver version 1.16ac)
May 10 15:22:41 david-desktop kernel: [ 52.905005] ppdev: user-space
parallel port driver
May 10 15:22:43 david-desktop kernel: [ 55.645982] Bluetooth: Core ver
2.13
May 10 15:22:43 david-desktop kernel: [ 55.650354] NET: Registered
protocol family 31
May 10 15:22:43 david-desktop kernel: [ 55.650367] Bluetooth: HCI
device and connection manager initialized
May 10 15:22:43 david-desktop kernel: [ 55.650377] Bluetooth: HCI
socket layer initialized
May 10 15:22:43 david-desktop kernel: [ 55.689761] Bluetooth: L2CAP
ver 2.11
May 10 15:22:43 david-desktop kernel: [ 55.689775] Bluetooth: L2CAP
socket layer initialized
May 10 15:22:43 david-desktop kernel: [ 55.720131] Bluetooth: BNEP
(Ethernet Emulation) ver 1.3
May 10 15:22:43 david-desktop kernel: [ 55.720145] Bluetooth: BNEP
filters: protocol multicast
May 10 15:22:43 david-desktop kernel: [ 55.797026] Bridge firewalling
registered
May 10 15:22:44 david-desktop kernel: [ 55.843590] Bluetooth: SCO
(Voice Link) ver 0.6
May 10 15:22:44 david-desktop kernel: [ 55.843627] Bluetooth: SCO
socket layer initialized
May 10 15:22:44 david-desktop kernel: [ 55.880168] Bluetooth: RFCOMM
socket layer initialized
May 10 15:22:44 david-desktop kernel: [ 55.880909] Bluetooth: RFCOMM
TTY layer initialized
May 10 15:22:44 david-desktop kernel: [ 55.880924] Bluetooth: RFCOMM
ver 1.10
May 10 15:22:48 david-desktop kernel: [ 60.135793] eth0: link down
-------------------------------------------------------------------------------end
Scanner is recognised by sane-find-scanner (sane-find-scanner -q):
found SCSI processor "HP C1130A 3614" at /dev/sg2
Scanner is recognised by scanimage (scanimage -L):
device `hp:/dev/sg2' is a Hewlett-Packard C1130A flatbed scanner
Scanimage does not appear to hang when I try to scan a picture. The
scanner goes through the motions and displays a large amount of data via
the terninal:
-------------------------------------------------------------------------------start
scanimage
P4
# SANE data follows
2550 4199
�O�����������������������������������?�����������������������������������������������������������������������������������������;������������������������������������������ ����������������������������������������������������������������������������������������������������������������������������������������������������������?���������������������������������������������������������������������������������������������������������������������������������}����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������?�������������������������������������������������������������������������������������������������
���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������7����������������������������������������������������������������������������������������������������������������k��������������������������������������������������������������������������������������������������������������������?���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������?������������������������������������������������������������������������������������������������������������������������������������&������������������������������������������������������������������������������������������������������������������������������������������/������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� ?�����������������������������������������������������������������������������������������������������������������������������������������������������������Y�������������������������������������������������������������������������������������������������������������������������������������������������������
-------------------------------------------------------------------------------end
Unfortunately i do not know how to use scanimage to be of any further
effective use.
Any suggestions? Do I need to try something different?
Thanks,
Dave
More information about the sane-devel
mailing list