[sane-devel] Agfa DuoScan SCSI scanner with Mac OS X 10.4

Fri Jul 22 11:40:14 UTC 2011

Hi Allan,

I have now disabled agfafocus and enabled microtek.
scanimage -L works now. This is great. Thank you!  

Unfortunately, I still can not scan a page. I get the following error message.

scanimage: sane_start: Error during device I/O

I have attached the output of scanimage at the end of this e-mail.
I have switched the debugging on for sanei_scsi and microtek.

I guess there might be a problem with the commands that are sent to the device.
Suggestions highly appreciated.

Werner

On 22.07.2011, at 12:51, m. allan noah wrote:
> Try changing /etc/sane.d/dll.conf. Disable agfafocus and make sure
> microtek is enabled.
> 
> allan

$ scanimage > Desktop/test.pnm
[sanei_debug] Setting debug level of microtek to 128.
[microtek] sane_init:  MICROTEK says hello! (v0.13.1)
[microtek] sane_init:  config-> # Uncomment following line to disable "real calibration" routines...
[microtek] sane_init:  config-> #norealcal
[microtek] sane_init:  config-> # Uncomment following line to disable "clever precalibration" routines...
[microtek] sane_init:  config-> #noprecal
[microtek] sane_init:  config-> #   Using "norealcal" will revert backend to pre-0.11.0 calibration code.
[microtek] sane_init:  config-> scsi * * Scanner
[microtek] attach_scanner:  <019bc800000000172dcdf573>
[microtek] attach_scanner:  opening <019bc800000000172dcdf573>
[sanei_debug] Setting debug level of sanei_scsi to 255.
[microtek] attach_scanner:  sending INQUIRY
[sanei_scsi] cmd2: cmd_size:6 src_size:0 dst_size:96 isWrite:0
[sanei_scsi] isRead dst_size:96
[sanei_scsi] Executing command
[sanei_scsi] ExecuteTaskSync OK Transferred 96 bytes
[microtek] id_microtek...
[microtek] 
[microtek] 
[microtek] 
[microtek] ========== Congratulations! ==========
[microtek] Your scanner appears to be supported  
[microtek] by the microtek backend.  However, it 
[microtek] has never been tried before, and some 
[microtek] parameters are bound to be wrong.     
[microtek] 
[microtek] Please send the scanner inquiry log in
[microtek] its entirety to mtek-bugs at mir.com and 
[microtek] include a description of the scanner, 
[microtek] including the base optical resolution.
[microtek] 
[microtek] You'll find complete instructions for 
[microtek] submitting an error/debug log in the  
[microtek] 'sane-microtek' man-page.             
[microtek] 
[microtek] 
[microtek] 
[microtek]  === SANE/Microtek backend v0.13.1 ===
[microtek] ========== Scanner Inquiry Block ========mm
[microtek] 06 00 01 01 5b 00 00 00 41 47 46 41 20 20 20 20 
[microtek] 44 55 4f 53 43 41 4e 20 20 20 20 20 20 20 20 20 
[microtek] 32 2e 33 30 53 43 53 49 20 46 57 20 56 33 2e 36 
[microtek] 20 43 54 4c 35 33 38 30 03 4f 8c c5 06 ee 5d 43 
[microtek] 01 03 47 00 00 83 00 01 0e 4a 07 05 00 00 00 00 
[microtek] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ff 
[microtek] ========== Scanner Inquiry Report ==========
[microtek] ===== Scanner ID...
[microtek] Device Type Code: 0x06
[microtek] Model Code: 0x5d
[microtek] Vendor Name: 'AGFA    '   Model Name: 'DUOSCAN         '
[microtek] Vendor Specific String: 'SCSI FW V3.6 CTL5380'
[microtek] Firmware Rev: '2.30'
[microtek] SCSI F/W version: 0.0     Scanner F/W version: 0.1
[microtek] Response data format: 0x01
[microtek] ===== Imaging Capabilities...
[microtek] Modes:  Lineart Halftone Gray Color (OnePass) 
[microtek] Resolution Step Sizes: 1% 5%    Expanded Resolution Support? yes
[microtek] Supported Bits Per Sample: 4 8 10 12 
[microtek] Max. document size code: 0x06
[microtek] Max. document size:  8299 x 13499 pixels
[microtek] Frame units:  pixels  1/8"'s 
[microtek] # of built-in halftones: 12   Downloadable patterns? Yes
[microtek] Data Compression: 
[microtek] Contrast Settings: 14   Exposure Settings: 74
[microtek] Adjustable Shadow/Highlight? yes   Adjustable Midtone? yes
[microtek] Digital brightness/offset? yes
[microtek] Gamma Table Size: 4096 entries of 2 bytes (max. depth: 12)
[microtek] ===== Source Options...
[microtek] Feed type:  flatbed    ADF support? yes
[microtek] Document Feeder Support? yes   Feeder Backtracking? yes
[microtek] Feeder Installed? no           Feeder Ready? no 
[microtek] Transparency Adapter Installed? yes
[microtek] Fast Color Prescan? no
[microtek] Selectable Transfer Format? no
[microtek] Color Transfer Sequence: line-by-line, non-sequential with headers
[microtek] Three pass scan support? no
[microtek] ModeSelect-1 and ModeSense-1 Support? yes
[microtek] Can Disable Linearization Table? no
[microtek] Can Disable Start-of-Scan Recalibration? no
[microtek] Internal expanded expansion? no
[microtek] ====== End of Scanner Inquiry Report =======
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_scsi] sanei_scsi_open: device name /dev/scanner is not valid
[sanei_debug] Setting debug level of sanei_scsi to 255.
[sanei_scsi] cmd2: cmd_size:6 src_size:0 dst_size:0 isWrite:1
[sanei_scsi] isWrite src_size:0
[sanei_scsi] Executing command
[sanei_scsi] ExecuteTaskSync OK Transferred 0 bytes
[sanei_scsi] cmd2: cmd_size:6 src_size:9 dst_size:0 isWrite:1
[sanei_scsi] isWrite src_size:9
[sanei_scsi] Executing command
[sanei_scsi] ExecuteTaskSync OK Transferred 9 bytes
[sanei_scsi] cmd2: cmd_size:6 src_size:0 dst_size:0 isWrite:1
[sanei_scsi] isWrite src_size:0
[sanei_scsi] Executing command
[sanei_scsi] ExecuteTaskSync OK Transferred 0 bytes
[sanei_scsi] cmd2: cmd_size:10 src_size:8192 dst_size:0 isWrite:1
[sanei_scsi] isWrite src_size:8192
[sanei_scsi] Executing command
[sanei_scsi] ExecuteTaskSync OK Transferred 8192 bytes
[sanei_scsi] cmd2: cmd_size:6 src_size:11 dst_size:0 isWrite:1
[sanei_scsi] isWrite src_size:11
[sanei_scsi] Executing command
[sanei_scsi] ExecuteTaskSync OK Transferred 11 bytes
[sanei_scsi] cmd2: cmd_size:6 src_size:10 dst_size:0 isWrite:1
[sanei_scsi] isWrite src_size:10
[sanei_scsi] Executing command
[sanei_scsi] ExecuteTaskSync OK Transferred 10 bytes
[sanei_scsi] cmd2: cmd_size:6 src_size:0 dst_size:0 isWrite:1
[sanei_scsi] isWrite src_size:0
[sanei_scsi] Executing command
[sanei_scsi] ExecuteTaskSync OK Transferred 0 bytes
[sanei_scsi] cmd2: cmd_size:6 src_size:0 dst_size:0 isWrite:1
[sanei_scsi] isWrite src_size:0
[sanei_scsi] Executing command
[sanei_scsi] ExecuteTaskSync OK Transferred 0 bytes
[sanei_scsi] cmd2: cmd_size:6 src_size:0 dst_size:6 isWrite:0
[sanei_scsi] isRead dst_size:6
[sanei_scsi] Executing command
[sanei_scsi] ExecuteTaskSync OK Transferred 6 bytes
[sanei_scsi] taskStatus = 0x00000002
[sanei_scsi] cmd2: cmd_size:6 src_size:0 dst_size:0 isWrite:1
[sanei_scsi] isWrite src_size:0
[sanei_scsi] Executing command
[sanei_scsi] ExecuteTaskSync OK Transferred 0 bytes
scanimage: sane_start: Error during device I/O