Hi Rolf -<div><br></div><div>Thanks for the reply. It seems I had to remove the sane packages installed by debian and re-build. However, I can't seem to figure out how to get a front end installed without wiping out the backend version. Even if I install a package, the try to re-build over the sane-backends upgrades, the backend doesn't upgrade and remains at 1.0.22. Is there something I'm missing? I've been using <a href="http://mp610.blogspot.com/">http://mp610.blogspot.com/</a> as my build advice. </div>
<div><br></div><div>Thanks!</div><div><br></div><div>Max</div><div class="gmail_extra"><br clear="all"><div>Max Resnick<br><a href="mailto:Max.Resnick@gmail.com">Max.Resnick@gmail.com</a><br>631-896-8357<br></div><br>
<br><br><div class="gmail_quote">On Mon, Dec 3, 2012 at 7:08 AM, Rolf Bensch <span dir="ltr"><<a href="mailto:webmaster@bensch-online.de" target="_blank">webmaster@bensch-online.de</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
Hi Max,<br>
<br>
your scanimage uses the 1.0.22 backend. It must be >=1.0.23.<br>
<br>
Please read README.linux and follow the installation desription.<br>
<br>
Cheers,<br>
Rolf<br>
<br>
Am 02.12.2012 22:54, schrieb Max Resnick:<br>
> Hi Everyone -<br>
><br>
> -Scanner Model is CanoScane 9000F - and is supported via<br>
> Pixma. <a href="http://www.sane-project.org/man/sane-pixma.5.html" target="_blank">http://www.sane-project.org/man/sane-pixma.5.html</a><br>
> -I'm running Debian Wheezy 64 Bit.<br>
> -I've also tried on Ubuntu 12.04 64 Bit.<br>
> -Scanner runs in windows just fine<br>
> -libusb-dev is installed via apt<br>
> I've ran with the distros installed package 1.0.22 (via APT), I've<br>
> also installed lasest from GIT. ./configure reports usb support<br>
> but lusb0_usb.h doesn't. I'm not sure if lusb0_usb is my issue?<br>
><br>
> I've got outputs from the following w/ debug enabled if applicable as<br>
> root and non-root user<br>
> -sane-find-scanner<br>
> -scanimage -L<br>
><br>
> Ultimately, I feel that somehow scanimage -L isnt't checking for USB<br>
> devices. I'm not sure how to force it via pixma.conf?<br>
><br>
> Again, thanks so much<br>
><br>
> ##scanimage (sane-backends) 1.0.24git; backend version 1.0.22##<br>
><br>
> ##sane-find-scanner##<br>
> ##Ran as root, Running as root recognized bus address but fails to<br>
> report the name of the device at bus address###<br>
> # sane-find-scanner will now attempt to detect your scanner. If the<br>
> # result is different from what you expected, first make sure your<br>
> # scanner is powered up and properly connected to your computer.<br>
><br>
> # No SCSI scanners found. If you expected something different, make<br>
> sure that<br>
> # you have loaded a kernel SCSI driver for your SCSI adapter.<br>
><br>
> found USB scanner (vendor=0x04a9 [Canon], product=0x1908 [CanoScan]) at<br>
> libusb:001:005<br>
> # Your USB scanner was (probably) detected. It may or may not be<br>
> supported by<br>
> # SANE. Try scanimage -L and read the backend's manpage.<br>
><br>
> # Not checking for parallel port scanners.<br>
><br>
> # Most Scanners connected to the parallel port or other proprietary ports<br>
> # can't be detected by this program.<br>
> ##Ran as non root user##<br>
> # sane-find-scanner will now attempt to detect your scanner. If the<br>
> # result is different from what you expected, first make sure your<br>
> # scanner is powered up and properly connected to your computer.<br>
><br>
> # No SCSI scanners found. If you expected something different, make<br>
> sure that<br>
> # you have loaded a kernel SCSI driver for your SCSI adapter.<br>
><br>
> found USB scanner (vendor=0x04a9, product=0x1908) at libusb:001:005<br>
> # Your USB scanner was (probably) detected. It may or may not be<br>
> supported by<br>
> # SANE. Try scanimage -L and read the backend's manpage.<br>
><br>
> # Not checking for parallel port scanners.<br>
><br>
> # Most Scanners connected to the parallel port or other proprietary ports<br>
> # can't be detected by this program.<br>
><br>
> # You may want to run this program as root to find all devices. Once you<br>
> # found the scanner devices, be sure to adjust access permissions as<br>
> # necessary.<br>
><br>
> ##sudo SANE_DEBUG_PIXMA=3 scanimage -L##<br>
> [sanei_debug] Setting debug level of pixma to 3.<br>
> [pixma] pixma is compiled with pthread support.<br>
> [pixma] pixma version 0.16.2<br>
> [pixma] sanei_bjnp_find_devices:<br>
> [pixma] wlan0 is IPv4 capable, sending broadcast..<br>
> [pixma] wlan0 is IPv4 capable, sending broadcast..<br>
> [pixma] wlan0 is IPv4 capable, sending broadcast..<br>
> [pixma] wlan0 is IPv4 capable, sending broadcast..<br>
> [pixma] wlan0 is IPv4 capable, sending broadcast..<br>
> [pixma] pixma_find_scanners() found 0 devices<br>
> device `v4l:/dev/video0' is a Noname Integrated Camera virtual device<br>
><br>
> ##SANE_DEBUG_PIXMA=3 scanimage -L##<br>
> [sanei_debug] Setting debug level of pixma to 3.<br>
> [pixma] pixma is compiled with pthread support.<br>
> [pixma] pixma version 0.16.2<br>
> [pixma] sanei_bjnp_find_devices:<br>
> [pixma] wlan0 is IPv4 capable, sending broadcast..<br>
> [pixma] wlan0 is IPv4 capable, sending broadcast..<br>
> [pixma] wlan0 is IPv4 capable, sending broadcast..<br>
> [pixma] wlan0 is IPv4 capable, sending broadcast..<br>
> [pixma] wlan0 is IPv4 capable, sending broadcast..<br>
> [pixma] pixma_find_scanners() found 0 devices<br>
> device `v4l:/dev/video0' is a Noname Integrated Camera virtual device<br>
><br>
><br>
> Max Resnick<br>
> <a href="mailto:Max.Resnick@gmail.com">Max.Resnick@gmail.com</a> <mailto:<a href="mailto:Max.Resnick@gmail.com">Max.Resnick@gmail.com</a>><br>
> <a href="tel:631-896-8357" value="+16318968357">631-896-8357</a><br>
><br>
</blockquote></div><br></div>