[sane-devel] Arcard and mustek

alto.iole at earthlink.net alto.iole at earthlink.net
Wed Jan 15 05:59:29 GMT 2003


Hi,
	base on your suggestion I checked out the output in debug mode. The inquiry
seems to me
OK, actually I cannot find any error except this
message before the exit
	
[mustek] sane_get_devices: 2 devices 

Is that OK ? I do not have two devices.


[sanei_debug] Setting debug level of mustek to 4.
[mustek] SANE mustek backend version 1.0 build 128 from sane-backends-1.0.9
[mustek] sane_init: reading config file `mustek.conf'
[mustek] sane_init: config file line 4: strip-height set to 1 inches
[mustek] sane_init: config file line 6: enabling force-wait
[mustek] sane_init: config file line 8: disabling double-buffering
[mustek] sane_init: config file line 11: trying to attach `scsi MUSTEK *
Scanner'
[mustek] sane_init: config file line 18: trying to attach `scsi SCANNER'
[mustek] attach: trying device /dev/sg0
[mustek] dev_open: /dev/sg0 is a SCSI device
[mustek] dev_open: wanted 8 kbytes, got 8 kbytes buffer
[mustek] attach: SCSI Vendor: `SCANNER ' Model: `                ' Rev.:
`1.01'
[mustek] attach: SCSI Type: Scanner; ANSI rev.: 1
[mustek] attach: SCSI flags: 
[mustek] attach: inquiry output:
[mustek]  06 00 01 01 5b 01 00 00 53 43 41 4e 4e 45 52 20  ....[...SCANNER 
[mustek]  20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20                  
[mustek]  31 2e 30 31 4d 55 53 54 45 4b 20 20 20 43 30 36  1.01MUSTEK   C06
[mustek]  20 53 31 32 49 44 57 4d 31 32 33 37 31 37 01 00   S12IDWM123717..
[mustek]  01 03 01 01 00 00 00 00 00 00 00 00 00 00 00 00  ................
[mustek]  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ff  ................
[mustek] attach: found Mustek scanner (new firmware format)
[mustek] attach: old firmware revision system
[mustek] attach: firmware revision 1.01
[mustek] attach: scanner id:  C06 S12IDW
[mustek] attach: this is probably a ScanExpress series A4 scanner
[mustek] attach: this is a single-pass scanner
[mustek] attach: scanner cover is closed
[mustek] attach: found Mustek ScanExpress 12000SP flatbed scanner, 1-pass, SE
[mustek] sane_init: config file line 25: trying to attach `/dev/scanner'
[mustek] attach: trying device /dev/scanner
[mustek] dev_open: /dev/scanner is a SCSI device
[mustek] dev_open: wanted 8 kbytes, got 8 kbytes buffer
[mustek] attach: SCSI Vendor: `SCANNER ' Model: `                ' Rev.:
`1.01'
[mustek] attach: SCSI Type: Scanner; ANSI rev.: 1
[mustek] attach: SCSI flags: 
[mustek] attach: inquiry output:
[mustek]  06 00 01 01 5b 01 00 00 53 43 41 4e 4e 45 52 20  ....[...SCANNER 
[mustek]  20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20                  
[mustek]  31 2e 30 31 4d 55 53 54 45 4b 20 20 20 43 30 36  1.01MUSTEK   C06
[mustek]  20 53 31 32 49 44 57 4d 31 32 33 37 31 37 01 00   S12IDWM123717..
[mustek]  01 03 01 01 00 00 00 00 00 00 00 00 00 00 00 00  ................
[mustek]  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ff  ................
[mustek] attach: found Mustek scanner (new firmware format)
[mustek] attach: old firmware revision system
[mustek] attach: firmware revision 1.01
[mustek] attach: scanner id:  C06 S12IDW
[mustek] attach: this is probably a ScanExpress series A4 scanner
[mustek] attach: this is a single-pass scanner
[mustek] attach: scanner cover is closed
[mustek] attach: found Mustek ScanExpress 12000SP flatbed scanner, 1-pass, SE
[mustek] sane_get_devices: 2 devices 
[mustek] sane_exit
device `mustek:/dev/scanner' is a Mustek ScanExpress 12000SP flatbed scanner
device `mustek:/dev/sg0' is a Mustek ScanExpress 12000SP flatbed scanner




More information about the sane-devel mailing list