[sane-devel] LIDE 60. configure scanning prefs?

[m. allan noah]

There are options for the image cropping area in the list, no? (-x -y, etc)

I don't know why you want uncalibrated data, it will look terrible.
How about you tell us what you are trying to do :)

allan

On Fri, Feb 11, 2011 at 2:49 PM, Ben Green <greenb1 at mac.com> wrote:
> Ha ha - thanks Allan - it worked.. and i pulled up the options too..
> HOWEVER - my (ongoing) problem is that i need to switch off the calibration section of the scan process so that i receive a raw data feed.
> Is there further settings I can effect? For example in the plustec backend, I was able to adjust crop area, gain, calibration on/off etc.. is this just not an option with genesys? Is there someone who can do such things? (certainly I can't - i couldn't even get the command into terminal!!)
>
>
>
>
>
> Thanks
>
>
> Ben
>
>
>
> On 11 Feb 2011, at 19:38, m. allan noah wrote:
>
>> It is a command. you run it in the terminal. If you got no text back,
>> try running this instead:
>>
>> scanimage -L
>>
>> allan
>>
>> On Fri, Feb 11, 2011 at 2:33 PM, Ben Green <greenb1 at mac.com> wrote:
>>>
>>>
>>> On 10 Feb 2011, at 05:24, stef wrote:
>>>
>>>> Le Wednesday 09 February 2011 18:01:08 Ben Green, vous avez écrit :
>>>>> Hi
>>>>> I'm trying to configure various actions inside my Lide 60 such as
>>>>> analogue gain, tinkering with the calibration and the crop area that
>>>>> it scans with.
>>>>>
>>>>> The backend seems to have been abandoned on the support front  -
>>>>> scanning is no problem, worked first time - its just this .conf file
>>>>> that i cannot drive? is there a list of commands I can feed into
>>>>> the .config file? like lamp on/off, red gain +3 ??? i'm afraid i dont
>>>>> speak Genesys?
>>>>>
>>>>> I have done this with some earlier LIDEs that worked with the plustec
>>>>> backend - these were quite straightforward - i could open the SANE
>>>>> prefs and turn calibration on/off, change gain and crop just by
>>>>> changing some zeros and ones.. however this genesys backend has only a
>>>>> list of scanners and their model/product addresses - I don't know what
>>>>> commands to put into the .conf file.
>>>>>
>>>>> I'm using SANE: mac10.6:
>>>>>
>>>>>   TWAIN SANE Interface 2.9 binary  http://www.ellert.se/twain-sane/
>>>>> SANE Preference Pane 0.9 binary http://www.ellert.se/twain-sane/ SANE
>>>>> backends http://www.sane-project.org/   libusb 0.1.13 beta 2009-09-10
>>>>> binary http://libusb.sourceforge.net/
>>>>>
>>>>>
>>>>> Any Help is Much Appreciated..
>>>>>
>>>>>
>>>>> Thnaks
>>>>>
>>>>>
>>>>> Ben
>>>>
>>>>       Hello,
>>>>
>>>>       all user settable settings are published by the backend through options.
>>>> You can get the full list of active options for your model with 'scanimage -d
>>>> genesys --help'. There is no options or settings to modify in the conf file.
>>>>
>>>> Regards,
>>>>       Stef
>>>>
>>>> --
>>>> sane-devel mailing list: sane-devel at lists.alioth.debian.org
>>>> http://lists.alioth.debian.org/mailman/listinfo/sane-devel
>>>> Unsubscribe: Send mail with subject "unsubscribe your_password"
>>>>             to sane-devel-request at lists.alioth.debian.org
>>>
>>>
>>> Hi Steph,
>>>
>>> Could you tell me how and where I use this command? (scanimage -d genesys --help)
>>> Is it in the SANE prefs file? if so, do i enter the command under my particular scanner model?
>>> I tried putting this command into terminal but got nothing back -
>>>
>>> Sorry I cant profess to know much about command line interface..
>>>
>>>
>>> Thanks for you help..
>>>
>>>
>>> Ben
>>>
>>>
>>>
>>> --
>>> sane-devel mailing list: sane-devel at lists.alioth.debian.org
>>> http://lists.alioth.debian.org/mailman/listinfo/sane-devel
>>> Unsubscribe: Send mail with subject "unsubscribe your_password"
>>>             to sane-devel-request at lists.alioth.debian.org
>>>
>>
>>
>>
>> --
>> "The truth is an offense, but not a sin"
>
>



-- 
"The truth is an offense, but not a sin"